Rondish Wireless Bed Leaving Alarm Sensor Mat Full Kit

Rondish Wireless Bed Leaving Alarm Sensor Mat Full Kit

It can be difficult for carers to always monitor their patients, particularly at nighttime. They may need to be taken to the toilet during the night, could fall out of bed or, if suffering from dementia, may be prone to wandering off. The more patients under your care, the more challenging it becomes to keep an eye on them all.

There are bed leaving sensor systems available which alert you if someone has left their bed, helping you know when you are needed. Typically, these are designed to monitor a single patient. But what if you work in a care home or hospital, with multiple patients in your care?

The Bed Leaving Alarm Sensor Mat Full Kit is unlike most standard bed leaving sensors in that it's capable of connecting to up to 99 different bed or chair sensors. This means you can keep tabs on a large amount of patients at once, so you won't have to be constantly checking on them all. With the Bed Leaving Sensor Kit, you can ensure you'll be alerted exactly when you're needed.

How Does the Bed Leaving Alarm Sensor Mat Full Kit Work?
The kit consists of everything you need to monitor when a patient gets out of bed. You simply place the bed sensor mat under the mattress or bed sheet at pelvis height. When the patient sits or lays down, the wireless transmitter acknowledges detection with two beeps.

When the patient leaves bed, an alarm signal is sent from the transmitter to the pager receiver, which can be attached to the carer's person using the provided belt clip to ensure they'll never miss an alert.

The carer will be signalled with sound or vibration, making it suitable for both the hearing and visually impaired. It also features a flashing LED light and will display which transmitter number is signaling. That way, if if you are monitoring multiple beds, you will know exactly which mat is being triggered so that you can quickly respond to the correct patient.

Adding Additional Mats
The kit is already set up to use with the provided sensor mat programmed as 'Number 1', but has the ability to connect with up to 99 mats on each pager. For each Additional Sensor Mat you wish to add, you must purchase an additional Wireless Transmitter to send the signal to your pager.

Additional Information
If the mattress is very thick, or the patient is of a slight build, it may be necessary to place the sensor mat on top of the mattress covered with another bed sheet, instead of underneath the mattress.

If using the sensor in conjunction with an electric blanket, then it is important the sensor goes beneath the mattress rather than beneath the sheet. Otherwise the heat might interfere with the sensor.

To ensure that the mat is functioning correctly, lie on the bed and then get up to check that the system is alerting as expected.

Key Features of the Alarm Sensor Mat Kit
Includes one bed sensor mat, wireless transmitter and pager receiver
Can connect with up to 99 bed sensor mats (only one included) to monitor multiple patients at once
Pager emits sound, vibration or combination of both to alert carer to patient leaving bed
Also has a flashing LED light, and displays/speaks the transmitter number so you know exactly which patient has left bed
Language button - can change the language of the spoken mat identification number, automatically set to English
Adjustable volume
Smart function - enables you to review the last 6 alarm calls
Low battery warning indicated by flashing LED
Pager has a belt clip so can be easily attached to person
Can also be placed in pocket or on a surface
Optional 15 minute alarm delay - allows patient to go to the toilet without triggering alarm, but will alert you if they have not returned to bed after 15 minutes
Can alternatively set device to alert you immediately
Reset button so you can reset the alarm once triggered
Pad lost warning light to alert you if sensor mat is not located by the system
Call button for panic alert or assistance alert
The transmitter has a connection port for the connection jack of the sensor mat to plug into - wire protection fitting protects the wire jack if the cable is pulled or yanked
Transmitter can be fixed to the wall or flat surface using the included two wall fixing housings
Technical Specifications
Dimensions (transmitter): 12cm tall, 7.7cm wide, 2.7cm thick
Dimensions (pager): 6.8cm tall, 8.5cm wide, 2.6cm thick (3.8cm thick if including belt clip)
Dimensions (sensor mat): 77cm long (85cm long if including cable protection housing), 51cm wide, less than 1cm thick
Cable length: approx. 205cm
Operating range: 100m (with clear line of sight)
9V 200mA adapter port (for mains operation - mains adapter sold separately)